Author Topic: 2017 New Old Stuff setup (Read 127211 times)

ndotcom · « **Reply #540 on:** Mar 04, 2014 at 04:43 PM »

Quote from: Nelson de Leon on Mar 04, 2014 at 04:31 PM

Kargahan na ng lead ang mga posts!!!

Mabigat na masyado eh, esep esep pa may ari kung ano ilalagay at kung saan ko bubutasan.

Quote from: joko11 on Mar 04, 2014 at 04:34 PM

kaw talaga konsi...nakakasama ang lead sa kalusugan

magkano damage ng stand brader norms?

Brader Joko damageable enough naman

Paggawa ka kay brader Jammy mas malapit sayo

joko11 · « **Reply #541 on:** Mar 04, 2014 at 05:11 PM »

Quote from: ndotcom on Mar 04, 2014 at 04:43 PM

Mabigat na masyado eh, esep esep pa may ari kung ano ilalagay at kung saan ko bubutasan.

Brader Joko damageable enough naman Paggawa ka kay brader Jammy mas malapit sayo

pwede na mercury dyan kapatid

at least hole lang ang gagawin para ipasok

wala pako pag gagamitan ng stands sa ngayon.pag meron na ulit hihingi ako kay jammy.ahehe..

redstarrising · « **Reply #542 on:** Mar 04, 2014 at 05:49 PM »

ayos brader norman

, pede rin filled with water para liquid ang sound

ndotcom · « **Reply #543 on:** Mar 04, 2014 at 06:17 PM »

Quote from: redstarrising on Mar 04, 2014 at 05:49 PM

ayos brader norman , pede rin filled with water para liquid ang sound

Yan nga sabi ng kapit bahay ko tubig hehehe, sabi ko intayin ko undas at candle wax lagay ko dyan patak patak sa butas

Tsnad · « **Reply #544 on:** Mar 10, 2014 at 10:16 AM »

boss musta yung 2a3 set amp mo tapos na ba...

ndotcom · « **Reply #545 on:** Mar 10, 2014 at 11:51 AM »

Boss ogie ayun nasa ilalim pa rin ng mesa, di ko natantsa ang bigat mukhang di ubra yung casing ko so palit muna then wiring na. Ikaw ala pa final decision? Traffo ang pinaka mabigat sa budget then paglikom ng parts, kaya sa sunod kit nalang ako para complete parts na agad tapos dito na pagawa ng traffos kasi mahal shipping nyan.

ndotcom · « **Reply #546 on:** Mar 10, 2014 at 03:04 PM »

Heto nalang, tapos na and maganda naman kinalabasan.

From this...

To this...

Test fit with the C7, sakto sa specs ko. Top plate is 272x300x12.5mm solid metal, cut hole is 50mm all sides, height without the spikes is 480mm(aprox 19inch).

mykel18 · « **Reply #547 on:** Mar 10, 2014 at 03:07 PM »

Ang ganda ng finish nga. Galing!

ndotcom · « **Reply #548 on:** Mar 10, 2014 at 03:16 PM »

Hirap nga mag masilya need more practice

. Pag di nakalagay C7 anlaki tignan ng stands kala ko sobra na yung specs ko sa base niya, pero nag iba pag nakapatong na speakers swakto lang. They compliment each other, di na malaki tignan si C7 lalo na pag malayo.

Tsnad · « **Reply #549 on:** Mar 10, 2014 at 03:21 PM »

Quote from: ndotcom on Mar 10, 2014 at 11:51 AM

Boss ogie ayun nasa ilalim pa rin ng mesa, di ko natantsa ang bigat mukhang di ubra yung casing ko so palit muna then wiring na. Ikaw ala pa final decision? Traffo ang pinaka mabigat sa budget then paglikom ng parts, kaya sa sunod kit nalang ako para complete parts na agad tapos dito na pagawa ng traffos kasi mahal shipping nyan.

ano maganda mono set amp or int lang..

redstarrising · « **Reply #550 on:** Mar 10, 2014 at 03:27 PM »

Ganda brader, swak na swak. Pina arawan mo pa sa sikat ng araw ha para maging warm sound

ndotcom · « **Reply #551 on:** Mar 10, 2014 at 03:34 PM »

Quote from: Tsnad on Mar 10, 2014 at 03:21 PM

ano maganda mono set amp or int lang..

If you have the cash eh di mono block na, additional cost sa case, power transformer and power rails(caps,diodes if SS, power tube if all tube).

tony · « **Reply #552 on:** Mar 10, 2014 at 03:37 PM »

Quote from: ndotcom on Mar 10, 2014 at 03:04 PM

Heto nalang, tapos na and maganda naman kinalabasan.

From this...

To this...

Test fit with the C7, sakto sa specs ko. Top plate is 272x300x12.5mm solid metal, cut hole is 50mm all sides, height without the spikes is 480mm(aprox 19inch).

ganda nyan kung powder coating.....

ndotcom · « **Reply #553 on:** Mar 10, 2014 at 03:46 PM »

Quote from: tony on Mar 10, 2014 at 03:37 PM

ganda nyan kung powder coating.....

Maganda nga sana sir Tony kaso di kaya ng powers ko i commute to, 10kgs or more isa.

Mga magkano kay sisingilin sa ganyan powder coat? Plus kailangan ba makinis na pag dalhin dun or sila na mag liha/masilya?

tony · « **Reply #554 on:** Mar 10, 2014 at 03:54 PM »

Quote from: ndotcom on Mar 10, 2014 at 03:46 PM

Maganda nga sana sir Tony kaso di kaya ng powers ko i commute to, 10kgs or more isa.

Mga magkano kay sisingilin sa ganyan powder coat? Plus kailangan ba makinis na pag dalhin dun or sila na mag liha/masilya?

minsan nagbubuhat ako ng bakal mula raon more than 10kg.....

kailangan lang strip mo yung paint, remove mo yung rust,
angle grinder mo para matanggal ang mga bulutong ng welding,
then pwede na....

ndotcom · « **Reply #555 on:** Mar 11, 2014 at 09:47 AM »

Sir Tony 10kgs kasi to sa left plus 10kgs to the right

tapos bulky pa kasi malalaki siya kaya di ko na try na ibyahe, plus madalang ang taxi dito sa bundok hehehe.

Mga amp/preamp case try ko minsan pa powder coat dun.

dodie · « **Reply #556 on:** Mar 11, 2014 at 10:49 AM »

pre ano ginamit mo na spikes? pektyur ng bottom

Superman · « **Reply #557 on:** Mar 11, 2014 at 10:49 AM »

Congratulations, sir! Excellent stands! Where did you have them made? Please PM me. Thanks!

Superman · « **Reply #558 on:** Mar 11, 2014 at 10:50 AM »

Quote from: dodie on Mar 11, 2014 at 10:49 AM

pre ano ginamit mo na spikes? pektyur ng bottom

Same question as well

ndotcom · « **Reply #559 on:** Mar 11, 2014 at 11:09 AM »

Quote from: dodie on Mar 11, 2014 at 10:49 AM

pre ano ginamit mo na spikes? pektyur ng bottom

Secret hehehe...

wait lang picturan ko di naman trade secret to kasi di to commercial, just pure pleasure of DIY.

Yan na yung spikes, yung nasa left side orig spikes na nataon may extra yung may ari so yan ginamit ko pag wala ay yung nasa right side gamit ko hex bolt(mas matigas) or any bolt and nut then pagrinder para pointed. Plus extra flange nut naman yung sa stands plate welded into place din sa loob para flushed at di kita sa labas.

Kita yung nut sa loob ng butas, flange siya para mas malaki surface area na ma weld sa tubular metal bago takpan yung base. Pwede pa rin gamitin na walang spikes kaso less 1 inch sa height.

forseti · « **Reply #560 on:** Mar 11, 2014 at 11:35 AM »

Quote from: ndotcom on Mar 10, 2014 at 03:04 PM

Heto nalang, tapos na and maganda naman kinalabasan.

From this...

To this...

Test fit with the C7, sakto sa specs ko. Top plate is 272x300x12.5mm solid metal, cut hole is 50mm all sides, height without the spikes is 480mm(aprox 19inch).

Quote from: tony on Mar 10, 2014 at 03:37 PM

ganda nyan kung powder coating.....

Very nice Norman!

ndotcom · « **Reply #561 on:** Mar 11, 2014 at 11:55 AM »

Thanks bro Lawrenz.

tony · « **Reply #562 on:** Mar 11, 2014 at 12:42 PM »

norman, paganahin na natin yung 2A3, mo pansamantala pwede 12by7 habang wala pa yung D3a mo....
pin connections lang ang babaguhin pag dating nung D3a mo...
para mapakinggan na natin sa Audio Nirvana at Mark audio FR's....

banesto · « **Reply #563 on:** Mar 13, 2014 at 06:52 PM »

Congrats sis Norms sa another DIY. kay pards doc ba yan?

audi · « **Reply #564 on:** Mar 13, 2014 at 07:01 PM »

Galing sir Norman ng pag kakagawa nyo sa speaker stand nyo...mas lalo na pogi si Harbeth.

dodie · « **Reply #565 on:** Mar 13, 2014 at 07:12 PM »

Quote from: ndotcom on Mar 11, 2014 at 11:09 AM

Secret hehehe...

wait lang picturan ko di naman trade secret to kasi di to commercial, just pure pleasure of DIY.

Yan na yung spikes, yung nasa left side orig spikes na nataon may extra yung may ari so yan ginamit ko pag wala ay yung nasa right side gamit ko hex bolt(mas matigas) or any bolt and nut then pagrinder para pointed. Plus extra flange nut naman yung sa stands plate welded into place din sa loob para flushed at di kita sa labas.

Kita yung nut sa loob ng butas, flange siya para mas malaki surface area na ma weld sa tubular metal bago takpan yung base. Pwede pa rin gamitin na walang spikes kaso less 1 inch sa height.

salamat sa pektyur bossing. nice nice!

ndotcom · « **Reply #566 on:** Mar 13, 2014 at 07:29 PM »

Yes Ka Ernie sa kanya yan at kinuha na agad

Bro Audi pinagawa lang yan at pattern ko si Harbeth ko. Same pa rin gamit ko stands na nakita niyo dati.

Boss chief Dodie no problem, kung makatulong yan eh good for us

Pag sa wood ka naman gagawa eh T-nuts naman ang maganda para sa thread, naka punch sa wood surface konting glue lang ayos na.

ndotcom · « **Reply #567 on:** Aug 11, 2015 at 06:47 AM »

I chance upon this turntable online and grab the chance, since this is considered the base model of my 1st table Thorens TD160 MKII I must have it.

So here it is needing a lot of TLC, all life is fading out of it and a shame to let it be.

I have to disassemble everything for a proper cleanup.

After a few days of grit removal, a bit of sand paper and scotch brite

Painted the top plate with black as well as the badge to show the AR logo.

Here it is all perked up

And ready to play, yehey I say !

mykel18 · « **Reply #568 on:** Aug 11, 2015 at 06:57 AM »

Nice nice! Marami ka na rin ba nabiling plaka dyan?

ndotcom · « **Reply #569 on:** Aug 11, 2015 at 07:05 AM »

Tagalog naman...

Natapos ang AR-XA project, syempre kailangan ng patungan. Nataon naman yung landlord ko nag uuwi ng pine wood ala paleta kaya heto nagawa.

Kailangan ng amp para mapakinggan ang AR-XA at meron naman pala sa ala ebay nila dito, pinalad nakakuha ng Pioneer A-207R MOS (mosfet integrated amp) may kasama pa Technics XR-35 CDP.

Speakers naman ang hanap, at nakita itong APinternational local brand nila dati mga 1980s daw.
8 inch poly at 1inch dome tweeter. Plus gawa na rin ng speaker stands at CAT6 na speaker cables bgay ng kabayan na fiber to home installer.

Yan po ang nagpapainit sa ating diwa habang nagkakape dito po sa malamig na lugar.