PinoyDVD: The Pinoy Digital Video & Devices Community
Home Theater => Audio => Tubes => Topic started by: FASTBACK on Aug 07, 2005 at 01:01 PM
-
This is the S.E.X (Single Ended eXperimentation) Kit Amplifier Rev 1.1
2 Watts Parallel single ended monoblock.
(http://groups.msn.com/_Secure/0VgCZAlEZlUnA1yWIzux6V0Q!FKQcwW35Z81lzGAtZ510BZxQFLqheO*YcyUh74ou4zNvVk53a4czTSkDeelw6FDe6sacwPtopojI7YaWpXrL7exHezBT2vewWCmEN7GA/Sex%20Amp%20Monoblock%20FV.jpg?dc=4675533953949509322)
The two monoblock side by side.
(http://groups.msn.com/_Secure/0TgCNAhwXlYzA1yWIzux6V4QWEiCFQPYikDDu9xEXHFyFl9Y4cHiKEPmPcmQTChFGMPq0YDrmk!ArBByDMB26*y7dpA*4i3zvTYag*PgcekljZTZ12rOGjg/Sex%20Amp%20stereo.jpg?dc=4675533954174772403)
Another View
(http://groups.msn.com/_Secure/0VQCJAgcZ6kHA1yWIzux6V0Q!FKQcwW35rl80*O*p4lNnCyOYkPpaMypIcRFO3WJj7jwG9643l!S97IhCZo3n86RtoAxNoimCXSmk56PtDMN4O7*uvGfoIMtEU3pCVtsV/Sex%20Amp%20Monoblock.jpg?dc=4675533953668693225)
http://www.wiredstate.com/forum/viewtopic.php?t=7269
-
bro,
congrats! you finally put it together na pala, very good job!
cheers!
-
JojoD
Thanks, finally after two long months I was able to hear a tube amp in my own system.
-
Read in a magazine "The best sounding tube amplifiers are those design with low wattage". Congratulation Sir! BTW, what speakers are you going to use?
-
Read in a magazine "The best sounding tube amplifiers are those design with low wattage". Congratulation Sir! BTW, what speakers are you going to use?
odyopayl
Thanks.
Presently the speakears I am using is also a DIY bought locally 4" driver and 1" tweeter only. But it fills my room with sweet music.
-
JojoD
Thanks, finally after two long months I was able to hear a tube amp in my own system.
So what is your initial impressions with the SEX amp? Any comments with regards to your ss gears? It is coupled to your DIY preamp right?
-
So what is your initial impressions with the SEX amp? Any comments with regards to your ss gears? It is coupled to your DIY preamp right?
I have compared it to my HT amp and the difference is night and day, I love the tube amps mids and highs very clear and soothing to my ears.
Presently the amp is coupled to my SS DIY preamp, I have yet to make a preamp. Hope to make one soon, and get a high sensitivity speakers for it as well.
-
hi master tony,
that is what i am currently doing it now! using VR tubes! ;D >:D ewan ko lng kung ultimate nga when i'm done! :D :D :D :D :D
fastback,
time to build that frank's ultimate tube preamp.....
-
fastback,
time to build that frank's ultimate tube preamp.....
Alright sir
just say when.
Thanks.
-
hi master tony,
that is what i am currently doing it now! using VR tubes! ;D >:D ewan ko lng kung ultimate nga when i'm done! :D :D :D :D :D
s2Kov
Good luck on your present project.
-
i have designs made and will make the prototype. features are:
1. voltage doubler using fred rectifier to two 1000ufd/250volts series connected caps.
2. filter choke then to 385ufd/450volt 105*C caps
3. all transistor regulation to 350volts for line stage, 305volts to phono amp stage.
4. 12volt dc supplies for heaters, 7025 heaters wired in series, separate heater supply for the upper 12bh7 stages,
5. power supply assembled on an FR4 glass epoxy board, instead of phonolic board.
6. power trasformer shall have copper foil electrostatic sheilds.
voltage doublers as opposed to full wave bridge is favored by many japanese designers! for tubes they are very attractive.
wow. very attractive indeed.
will wait for the initial result of the prototype, for now time to search for sources of the caps and the FR4 boards.
Thanks
-
Thanks! ;D
s2Kov
Good luck on your present project.
-
drooling! >:D
master tony, do you have source for 7025 tube?
i have designs made and will make the prototype. features are:
1. voltage doubler using fred rectifier to two 1000ufd/250volts series connected caps.
2. filter choke then to 385ufd/450volt 105*C caps
3. all transistor regulation to 350volts for line stage, 305volts to phono amp stage.
4. 12volt dc supplies for heaters, 7025 heaters wired in series, separate heater supply for the upper 12bh7 stages,
5. power supply assembled on an FR4 glass epoxy board, instead of phonolic board.
6. power trasformer shall have copper foil electrostatic sheilds.
voltage doublers as opposed to full wave bridge is favored by many japanese designers! for tubes they are very attractive.
-
nyahaha! ;D lapit na yan! ;D
email mo skin kpag tapos na! :D
-
Getting excited already just looking at the pictures of the tranny.
Lapit na nga, this will match the tranny of my S.E.X amp.
Thanks
-
Wow already done.
Now time to start complete the remaining parts of the preamp.
Thanks Sir. 8)