Topic: Yamaha Receivers

[Courage]

Good day guys,

ask ko lang nanonoud ako ng movie ka gabi and i just noticed
that my DSP A1 left channel ay medyo mahina compare sa center at right channel..

so i did test tone same parin at i tried the right speaker connect to the left (baka speaker yung sira) so i could confirm nga mahina talaga..

ano po problem nito?

TIA

Check the Speaker Configuration Levels of left and right channel in receiver
Check the source playing, may source kasi minsan na talagang di pantay ang output
Check the connection of + and - sa speaker
Check the Balance setting of your receiver
Kung playing from PC or Laptop may balance setting din

[2fast2furious]

Good day guys,

ask ko lang nanonoud ako ng movie ka gabi and i just noticed
that my DSP A1 left channel ay medyo mahina compare sa center at right channel..

so i did test tone same parin at i tried the right speaker connect to the left (baka speaker yung sira) so i could confirm nga mahina talaga..

ano po problem nito?

TIA

from your test scenario, it seems your left channel amp has an issue. have it check by reputable shops na din. (not sure though kung may reset yung DSP A1 para factory default yung setting)

[jackdee]

Check the Speaker Configuration Levels of left and right channel in receiver
Check the source playing, may source kasi minsan na talagang di pantay ang output
Check the connection of + and - sa speaker
Check the Balance setting of your receiver
Kung playing from PC or Laptop may balance setting din

i tried everything bro. ganun parin ngayun ko lang na noticed. huhuhuhu pa check ko bukas..

from your test scenario, it seems your left channel amp has an issue. have it check by reputable shops na din. (not sure though kung may reset yung DSP A1 para factory default yung setting)

AFAIK pag na unplug ko si DSP then when i get watch movied nag ddfault cya.




ano po ba ang case nito isnt my voltage? kasi minsan nag lolow volatge ako dito.. im using only power grid 1k watts 

[Courage]

i tried everything bro. ganun parin ngayun ko lang na noticed. huhuhuhu pa check ko bukas..


AFAIK pag na unplug ko si DSP then when i get watch movied nag ddfault cya.




ano po ba ang case nito isnt my voltage? kasi minsan nag lolow volatge ako dito.. im using only power grid 1k watts 

Everytime you unplug and plug it again nag rereset lahat nang settings to default?

[jackdee]

Everytime you unplug and plug it again nag rereset lahat nang settings to default?

yes bro. kung naka plug lang yun avr ko.. pero yung naka switch off sa avr. hindi cya na ddfault.

but kung unplug lahat back to dfault.

[Courage]

yes bro. kung naka plug lang yun avr ko.. pero yung naka switch off sa avr. hindi cya na ddfault.

but kung unplug lahat back to dfault.

Means you have a faulty battery or capacitor.. Madali lang palitan yun... mas nakaka worry yung hindi pantay ang tunog nang left and right channel mo... So basically your receiver has two issues... Bring it to Service center na and have it checked.. Sayang yan, High end and really nice sounding receiver..

[jackdee]

Means you have a faulty battery or capacitor.. Madali lang palitan yun... mas nakaka worry yung hindi pantay ang tunog nang left and right channel mo... So basically your receiver has two issues... Bring it to Service center na and have it checked.. Sayang yan, High end and really nice sounding receiver..

oo nga im worried talaga. i did adjust the balance kasi sa DSP you cant adjust to the remote
nasa front panel yung balance nya, so adjust ko -2 to the left para pantay sila..

but iba talaga pag balance. huhuhu

[Clondalkin]

First aid muna

Have you tried shorting the Pre-Out and the Power- Amp-In connectors of all channels?

[reynold]

Hi Jackdee,

I have a DSP-A1 which was replaced only yesterday by Onkyo 805, but from my experience with DSP-A1, di naman nangyayari sa unit ko yung mga issues mo... Have it check with a professional technician, sayang yan, one of the best sounding receiver pa rin yan until now, DSP-A1 is still a beast...

[jackdee]

Hi Jackdee,

I have a DSP-A1 which was replaced only yesterday by Onkyo 805, but from my experience with DSP-A1, di naman nangyayari sa unit ko yung mga issues mo... Have it check with a professional technician, sayang yan, one of the best sounding receiver pa rin yan until now, DSP-A1 is still a beast...

nice to hear from you bro. ikaw lang ang hinihintay ko mag give comment
kasi ikaw lang may DSP na active dito hihihi

try ko mamaya thru pre-outs baka walang sugat. huhuhu


i love this amp since i owned yamaha 1500 before.

yes its a beast amp bro. na iinis ako mag linis ng kwarto ko ang bigat kasi 

[cookies]

Hello mga sirs,
Ask lang po ako ng tulong nyo regarding the remote control of my R-XV 730, di po gumagana yung volume control nung remote, pero working yung ibang functions. Meron po bang universal remote control for yamaha receivers, and saan po kaya pwedeng makabili kung meron. Kahit po 2nd hand ok na sakin.
Many thanks in advance.

[merdenoms]

i'm using an rx-373 amplifier and my computer pc as a source of HD movies, the two are bridged by spdif so  the pc could transfer the sound data to my amplifier and send it to my speakers. My question is, what settings on my amplifier is suitable for watching ripped bluray movies 5.1 DTS?


Currently, im using 5.1 stereo channel (cinema dsp) on my amplifier..... napansin ko lang parang lahat ng boses lumalabas sa front, center, at left speakers. I also tried Pro Logic pero hindi tumutunog yung sub ko. May mali ba sa settings ko? Dapat ba while watching HD movies 5.1 stereo channel ang gamitin?

Maraming salamat!

[raider125jeigh]

i'm using an rx-373 amplifier and my computer pc as a source of HD movies, the two are bridged by spdif so  the pc could transfer the sound data to my amplifier and send it to my speakers. My question is, what settings on my amplifier is suitable for watching ripped bluray movies 5.1 DTS?


Currently, im using 5.1 stereo channel (cinema dsp) on my amplifier..... napansin ko lang parang lahat ng boses lumalabas sa front, center, at left speakers. I also tried Pro Logic pero hindi tumutunog yung sub ko. May mali ba sa settings ko? Dapat ba while watching HD movies 5.1 stereo channel ang gamitin?

Maraming salamat!

check mo maige ung file kung DTS ..minsan kasi sa folder name DTS pero hindi pala...


did you try other files?
check your manual hahaha..just kidding...
kindly check the option na dapat dts ang lalabas

[merdenoms]

yep sir... lahat na po tinry ko na HD rip na lahat 5.1 dts ganon pa din lumalabas sa amplifier (5.1 stereo). Dapat ba lalabas pa rin si DTS dun sa yamaha amplifier kahit wala pa akong surround speakers?

[raider125jeigh]

yep sir... lahat na po tinry ko na HD rip na lahat 5.1 dts ganon pa din lumalabas sa amplifier (5.1 stereo). Dapat ba lalabas pa rin si DTS dun sa yamaha amplifier kahit wala pa akong surround speakers?

DTS ang dapat lumabas dun mapa HDMI or optical ang gamit

btw anu ba source mo? PC right?
not sure kung may gagalawin ka sa setting sa pc - somehow like bitstream para ung avr ang magdecode..
standard surr?  kalikotin mo ung mga dsp na pagpipilian dapat lalabas ang DTS
try mo DOLBY

[merdenoms]

pinindot ko din yung program.. ang lumalabas lang stereo, 5.1 stereo, pro logic (hindi tumutunog yung subwoofer pag pinili ko). Sige, basa basa muna ako ng manual. Tancha ko baka meron pang iibahin sa computer e para passthrough lang ang gawin nya papunta sa amplifier

[raider125jeigh]

pinindot ko din yung program.. ang lumalabas lang stereo, 5.1 stereo, pro logic (hindi tumutunog yung subwoofer pag pinili ko). Sige, basa basa muna ako ng manual. Tancha ko baka meron pang iibahin sa computer e para passthrough lang ang gawin nya papunta sa amplifier

kasi kung lumalabas lang e 5.1 or 7.1 ang natatangap malamang ni avr is stereo den pwede nya somehow iconvert with the following option pero kapag DTS ung natangap lalabas ung DTS da receiver

[trinity1123]

i'm using an rx-373 amplifier and my computer pc as a source of HD movies, the two are bridged by spdif so  the pc could transfer the sound data to my amplifier and send it to my speakers. My question is, what settings on my amplifier is suitable for watching ripped bluray movies 5.1 DTS?


Currently, im using 5.1 stereo channel (cinema dsp) on my amplifier..... napansin ko lang parang lahat ng boses lumalabas sa front, center, at left speakers. I also tried Pro Logic pero hindi tumutunog yung sub ko. May mali ba sa settings ko? Dapat ba while watching HD movies 5.1 stereo channel ang gamitin?

Maraming salamat!

Kahit 5.1 DTS ripped yang file mo kung wala naman DTS capability yang sound card mo,di talaga lalabas yan dun sa Amp. mo

[merdenoms]

^sir, i'm using on board soundcard with spdif/optical out..... hindi ba dapat isesend ni PC yung sound(raw) sa amplifier via optical cable at bahala na si amplifier mag process ng DTS?

[Courage]

^sir, i'm using on board soundcard with spdif/optical out..... hindi ba dapat isesend ni PC yung sound(raw) sa amplifier via optical cable at bahala na si amplifier mag process ng DTS?

You should check your PC if it's bitstreaming the DD or DTS. What player are you using?

[merdenoms]

i'm using VLC or KMPlayer sir =) might try this next saturday.

How to force VLC to use S/PDIF.

first go to Tools >> Preferences >> Audio, and then under "Output Module", select "Win32 waveOut extension output." You should now see a check box that says "Use S/PDIF when available." Tick it, click "Save" and you should be good to go.


Eto na kaya ang sagot sa aking katanungan?

[Wildfire™]

i'm using VLC or KMPlayer sir =) might try this next saturday.

How to force VLC to use S/PDIF.

first go to Tools >> Preferences >> Audio, and then under "Output Module", select "Win32 waveOut extension output." You should now see a check box that says "Use S/PDIF when available." Tick it, click "Save" and you should be good to go.


Eto na kaya ang sagot sa aking katanungan?

oo settings lang ng player yan 

[Courage]

i'm using VLC or KMPlayer sir =) might try this next saturday.

How to force VLC to use S/PDIF.

first go to Tools >> Preferences >> Audio, and then under "Output Module", select "Win32 waveOut extension output." You should now see a check box that says "Use S/PDIF when available." Tick it, click "Save" and you should be good to go.


Eto na kaya ang sagot sa aking katanungan?

Also make sure that the Audio of your source is DD or DTS, may files kasi na may Multiple Audio eh...

[merdenoms]

okay na mga sir. inayos ko lang yung configuration ng XBMC na dapat naka digital output. naglalaro na yung tunog pag nanonood ako ng HD movies =)

[Allan_2180]

Got this Yamaha Aventage RX-A810 from a fellow pdvd member:



It really goes well with my inexpensive Wharfedale Diamond 9.6 and
the sound become more livelier and has improved mids and highs as
compared with my old HarmanKardon AVR240 which is more on a laid-back side.
Dual HDMI Out is really convenient when you have both TV and Projector setup.

It's network function is simply awesome and the AV Controller App works well
with Android phone too!

[Courage]

Got this Yamaha Aventage RX-A810 from a fellow pdvd member:



It really goes well with my inexpensive Wharfedale Diamond 9.6 and
the sound become more livelier and has improved mids and highs as
compared with my old HarmanKardon AVR240 which is more on a laid-back side.
Dual HDMI Out is really cenvenient when you have both TV and Projector setup.

It's network function is simply awesome and the AV Controller App works well
with Android phone too!

Congratulations sir... Aventage ROCKS!!!!!

[NeilJohn]

Hi Guys,

Where's the best place to go for Yamaha Aventage receivers? Would this be a good partner to the PSB image series/ PSB imagine mini / dali zensors?

Your replies would be much appreciated!

Cheers!

[Stagea]

Hi Guys,

Where's the best place to go for Yamaha Aventage receivers? Would this be a good partner to the PSB image series/ PSB imagine mini / dali zensors?

Your replies would be much appreciated!

Cheers!

North American release lang po ata yung Aventage series. May RX-V equivalent models na available dito sa atin.

Try mo contact Watt HiFi if you want to try yung pairing ng PSB at Yamaha.

[NeilJohn]

Thanks Sir,

I'm currently looking at Yamaha, onkyo, and Denon receivers to pair with PSB. I've been smitten with the imagine minis when I first saw them, haven't heard them yet but it made me willing to slowly build my system up instead of getting the whole 5.1 at a snap. Unless of course the wife objects. The AV shop at timog recommended NAD to pair with PSB or even the blackstones as I'm after something small but the NAD is not within budget. I've also considered the B4s (seen the B5s) and its not that  pleasing aesthetically (important to the wife). Also considering B&W M-1s (already have the approval from the wifey) and the ASW608 as combo because the form factor and the reviews are quite favourable.

I'm a bit averse to bright sounding systems as I find them too fatiguing. Given my choices, would you suggest other options? Budget should be not more than 90k, the lower the better. Willing to build up slowly to significantly reduce costs.

Sorry for the long reply.

Thanks.

North American release lang po ata yung Aventage series. May RX-V equivalent models na available dito sa atin.

Try mo contact Watt HiFi if you want to try yung pairing ng PSB at Yamaha.

[Stagea]

Thanks Sir,

I'm currently looking at Yamaha, onkyo, and Denon receivers to pair with PSB. I've been smitten with the imagine minis when I first saw them, haven't heard them yet but it made me willing to slowly build my system up instead of getting the whole 5.1 at a snap. Unless of course the wife objects. The AV shop at timog recommended NAD to pair with PSB or even the blackstones as I'm after something small but the NAD is not within budget. I've also considered the B4s (seen the B5s) and its not that  pleasing aesthetically (important to the wife). Also considering B&W M-1s (already have the approval from the wifey) and the ASW608 as combo because the form factor and the reviews are quite favourable.

I'm a bit averse to bright sounding systems as I find them too fatiguing. Given my choices, would you suggest other options? Budget should be not more than 90k, the lower the better. Willing to build up slowly to significantly reduce costs.

Sorry for the long reply.

Thanks.

You probably visited Audible Illusions. They're quite accommodating, and they should be able to help with your needs.

The PSB HD10 is a long shot ahead of the B&W ASW608 when it comes to movie performance, if you're really after a small form factor.

The Imagine series speakers need quite some current, so I suggest going for a midlevel or higher AVR.