Topic: ONKYO AVR

[wengkapre]

nasa cabinet ba yung avr mo sir? an auxiliary fan would help:

[trailrider]

Sir Weng,

 Thank u po sa advice, I'll try to put a cooling fan just as you suggested.

[penti]

I agree with the fan. The interior of the AVR can get pretty hot, pretty fast. Wish I did something similar since had a glass divider two inches above the top of the AVR.

My Onkyo's HDMI board died on me a few months ago, and thinking this could be one cause (on top of subpar quality boards they used on some production runs, as confirmed by Onkyo some months ago). Would cost me 15k to replace, so opting to use my HDMI Front with an HDMI switch.

[kangkaroth]

did this too. although the 626 has a built-in fan, i didnt want to risk it getting that hot. thats why i too placed another fan on top. parang ke sir wengkapre.

[tein]

★★ Onkyo Dolby Atmos Receiver Promo! ★★

►►Get a FREE IE-FC300 In-Ear Headphones worth Php4,950 when you purchase (1) of the Onkyo Dolby Atmos Enabled A/V Receivers below.

♦ Onkyo TX-NR636 7.2 : P39,000
♦ Onkyo TX-NR737 7.2 : P49,000
♦ Onkyo TX-NR838 7.2 : P59,000

°°Offer valid from Oct 1 to Oct 31 2014 only!!!

0917-5160808
708-3122

[Moks007]

Grabe so tempted with the 636, pero I read puede Lang up to 5.1.2? Hindi puede 5.1.4? I want na Dolby atmos!!! Hehehe

[tein]

Hehe just PM me for special PDVD price

[wengkapre]

did this too. although the 626 has a built-in fan, i didnt want to risk it getting that hot. thats why i too placed another fan on top. parang ke sir wengkapre.

hindi po sa akin yan yamaha avr sir, image link po yan
hehehe onkyo owner din po ako 

[Moks007]

Hehe just PM me for special PDVD price

Sure will sir, kung ready na hehe. Thanks a lot.

[kangkaroth]

hindi po sa akin yan yamaha avr sir, image link po yan
hehehe onkyo owner din po ako 

oops my bad, kala ko inyo, hehehe

[DViant]

What are the choice onkyo av receivers released in 2014? Take note, never said the best.

[backdraft]

sirs,

I have problem with my onkyo 508 na 110V which plugged in sa 110v outlet and when I'm watching movies then meron sobrang lakas na LFE eh nag rerestarted yung AVR. Saglit lang naman mga 2 seconds naka ON na ulit yung avr. pero when I lower the volume on the same scene na may malakas na LFE di naman nag rereset?

Any advice?

TIA!

[Nelson de Leon]

sirs,

I have problem with my onkyo 508 na 110V which plugged in sa 110v outlet and when I'm watching movies then meron sobrang lakas na LFE eh nag rerestarted yung AVR. Saglit lang naman mga 2 seconds naka ON na ulit yung avr. pero when I lower the volume on the same scene na may malakas na LFE di naman nag rereset?

Any advice?

TIA!

Check your speaker settings. Baka kailangan itaas ang xover point so low frequencies won't go through the speakers. Ganyan din old Pio ko.

[backdraft]

^ sir nelson. my xovers are set to 80. itaas ko pa to 100?

[Nelson de Leon]

^ sir nelson. my xovers are set to 80. itaas ko pa to 100?

Yes try mo and play at the same volume and the same track. Kapag hindi nag-trip, yun na yun.

[backdraft]

Yes try mo and play at the same volume and the same track. Kapag hindi nag-trip, yun na yun.

what if nag reset pa ulit ano pa pwede gawin sir?

[Nelson de Leon]

what if nag reset pa ulit ano pa pwede gawin sir?

Itaas mo sa 120hz.

[ultimatedls]

sirs,

I have problem with my onkyo 508 na 110V which plugged in sa 110v outlet and when I'm watching movies then meron sobrang lakas na LFE eh nag rerestarted yung AVR. Saglit lang naman mga 2 seconds naka ON na ulit yung avr. pero when I lower the volume on the same scene na may malakas na LFE di naman nag rereset?

Any advice?

TIA!

shutdown! 508 couldn't handle it. Tama si sir Nelson try to lower x over or if don't push the receiver too much baka power hungry din mga speakers mo. Under powered speakers can lead to damage on receiver and speakers

[Hammerheart]

sirs,

I have problem with my onkyo 508 na 110V which plugged in sa 110v outlet and when I'm watching movies then meron sobrang lakas na LFE eh nag rerestarted yung AVR. Saglit lang naman mga 2 seconds naka ON na ulit yung avr. pero when I lower the volume on the same scene na may malakas na LFE di naman nag rereset?

Any advice?

TIA!

Sir recheck mo speaker cables/ connectors mo. Looks like me shorted.

[backdraft]

I've tried lowering the xover to 120 but it's still the same. nag rereset pa din sa malakas na lfe.

I've check my wires naman wala naman shorted bro.

[olrac]

hi just want to check form the experts... I was going through my audessy setting and found that the crossover set for my LCR and surrounds is at 40hz.  ok lang ba to or should i set it a 80hz?  i tried setting it a 80 pero parang wala namang noticeable difference so i just set it back at 40.  Suggestion is highly appreciated baka mas recommended to set it at 80 even if there is no difference (i think) or should i just leave it based on the calibration result. Im using polk RTi series for my LCR.

TIA.

[♡ lvcdg23™ ✌]

hi just want to check form the experts... I was going through my audessy setting and found that the crossover set for my LCR and surrounds is at 40hz.  ok lang ba to or should i set it a 80hz?  i tried setting it a 80 pero parang wala namang noticeable difference so i just set it back at 40.  Suggestion is highly appreciated baka mas recommended to set it at 80 even if there is no difference (i think) or should i just leave it based on the calibration result. Im using polk RTi series for my LCR.

TIA.

What are your Left, Center and Right speakers?

[yygoob]

hi just want to check form the experts... I was going through my audessy setting and found that the crossover set for my LCR and surrounds is at 40hz.  ok lang ba to or should i set it a 80hz?  i tried setting it a 80 pero parang wala namang noticeable difference so i just set it back at 40.  Suggestion is highly appreciated baka mas recommended to set it at 80 even if there is no difference (i think) or should i just leave it based on the calibration result. Im using polk RTi series for my LCR.



TIA.

most advice in the net is to set it at 80....pero i guess preference lang talaga.... most onkyo receiver would set it lower than 80 unless siguro satellite speakers mo.....in my case 40 din yung sinet ng onkyo pero i measured the frequency readings front and subwoofer together...mas flat kung 80 ang settings...sa pandinig ko rin mas ok and 80...hope this help

[olrac]

@louie - I'm using Polk rti a5 and cs 10

@yygoob - thanks sir been reading from the net and suggested is at 80 nga. Will try again if there will be difference using 80.


Also noticed that my ohm rating was set at 6ohms and based from Polk specs my LCR is at 8ohms. Tried changing it in my AVR but options are 4 and 6 only. Ok Lang kaya Ito? Feeling ko naman di di nahihirapan ung AVR.

[♡ lvcdg23™ ✌]

^ Ok lang to set it at 6ohms...
Set your fronts and center na lang to 80Hz...
Then the LPF for LFE to 120Hz.

[olrac]

^ Ok lang to set it at 6ohms...
Set your fronts and center na lang to 80Hz...
Then the LPF for LFE to 120Hz.

ok sir. cge will set it at 80 as suggested and recommended. baka mas gumanda pa nga ang tunog.

[plapoy]

Mga master. Need your advise. Yung onkyo 608 ko parang naghang sya.. kapag nakaplug sya kusa nabubuhay tapos no response sa remote or kahit anong button at volume.. na try ko ireset pero ganon pa din.. any suggestion? Us version pla yung sakin 110v. Salamat sa tutulong..

[shoktongxxx]

sirs,

I have problem with my onkyo 508 na 110V which plugged in sa 110v outlet and when I'm watching movies then meron sobrang lakas na LFE eh nag rerestarted yung AVR. Saglit lang naman mga 2 seconds naka ON na ulit yung avr. pero when I lower the volume on the same scene na may malakas na LFE di naman nag rereset?

Any advice?

TIA!

solve na ba ito? dati kasi may na encounter din ako ganito sa 508 ko, try mo sir configure yung sa SP Config, set mo yung front mo to Small speakers pag naka set kasi sa Large talagang nangyayari to sa Onkyo 508 eh lalo na kung naka set pa sa on yung Double Bass..HTH.

[backdraft]

solve na ba ito? dati kasi may na encounter din ako ganito sa 508 ko, try mo sir configure yung sa SP Config, set mo yung front mo to Small speakers pag naka set kasi sa Large talagang nangyayari to sa Onkyo 508 eh lalo na kung naka set pa sa on yung Double Bass..HTH.

solved na to sir. 110v kasi yung onkyo and naka plug sa 110v outlet. eh naisip kong gumamit ng step down transformer at rekta sa 220v. ayun so far ok na. tingin ko hindi maganda grounding ng 110v kaya kinukulang sa kuryente.

[shoktongxxx]

solved na to sir. 110v kasi yung onkyo and naka plug sa 110v outlet. eh naisip kong gumamit ng step down transformer at rekta sa 220v. ayun so far ok na. tingin ko hindi maganda grounding ng 110v kaya kinukulang sa kuryente.

ah ok, 220V naman gamit ko sa 508 eh..baka magkaiba lang tayo na encounter na problem.