Author Topic: ONKYO AVR (Read 536780 times)

Sir Louie d bagay sayo ang lumang model like the 5009. 5010 dapat for you. Go na po para may sumagot sa requested users review ni Emir Darwin at mabasa din namin.

raider125jeigh · « **Reply #3036 on:** Oct 16, 2012 at 01:00 PM »

Quote from: Louie_18 on Oct 16, 2012 at 10:58 AM

Tirahin mo na yung Onkyo 3008 sis!!!
Yung Onkyo 5009 kaya maganda?

hahaha....hopefully - faithfully

♡ lvcdg23™ ✌ · « **Reply #3037 on:** Oct 16, 2012 at 02:09 PM »

Quote from: vgsison on Oct 16, 2012 at 11:13 AM

Sir Louie d bagay sayo ang lumang model like the 5009. 5010 dapat for you. Go na po para may sumagot sa requested users review ni Emir Darwin at mabasa din namin.

Naku hindi ko na kaya yung Onkyo 5010. Masyado pang mahal... Baka next year paglabas nung Onkyo 5011 baka kaya na yung 5010, hehehe

Quote from: raider125jeigh on Oct 16, 2012 at 01:00 PM

hahaha....hopefully - faithfully

Kayang kaya yan sister!!!

defcon3 · « **Reply #3038 on:** Oct 16, 2012 at 02:19 PM »

Quote from: joko11 on Oct 15, 2012 at 09:08 PM

maari bang malaman kung anong krimen ang magaganap?

may naamoy akong malaking pasabog................ng utot

defcon3 · « **Reply #3039 on:** Oct 16, 2012 at 02:21 PM »

Quote from: Louie_18 on Oct 16, 2012 at 10:58 AM

Tirahin mo na yung Onkyo 3008 sis!!!
Yung Onkyo 5009 kaya maganda?

tirahin na ng tirahin...wag na palagpasin ung opportunidad.....pasok lang ng pasok...bahala na kung magalet si kumander.....hahaha

♡ lvcdg23™ ✌ · « **Reply #3040 on:** Oct 16, 2012 at 02:59 PM »

Quote from: defcon3 on Oct 16, 2012 at 02:21 PM

tirahin na ng tirahin...wag na palagpasin ung opportunidad.....pasok lang ng pasok...bahala na kung magalet si kumander.....hahaha

Ipikit na lang ang mga mata pagdumapo na ang latigo

jao143 · « **Reply #3041 on:** Oct 23, 2012 at 05:33 PM »

Questions mga bros, I'm currently using an onkyo 818. What setting should I use in the speaker set up when I use Left, Right, Center SVS M01 speakers na 4ohms, and an SVS SSS-02 speakers na 8ohms?

Is it also safe for the AVR to use speakers with different impedance?

Thanks.

elim · « **Reply #3042 on:** Oct 23, 2012 at 05:38 PM »

Hi Jao,
The 818 might have a hard time with that combination. AFAIK the onkyos can handle different impedances if they're 6 and 8 ohms. however sa literature niya its indicated to avoid using different impedences. If you'd still want to try the setting should be at 4ohms.

jao143 · « **Reply #3043 on:** Oct 23, 2012 at 05:47 PM »

Quote from: elim on Oct 23, 2012 at 05:38 PM

Hi Jao,
The 818 might have a hard time with that combination. AFAIK the onkyos can handle different impedances if they're 6 and 8 ohms. however sa literature niya its indicated to avoid using different impedences. If you'd still want to try the setting should be at 4ohms.

Thank you sir

I guess the best way to go is to use an external power amp

elim · « **Reply #3044 on:** Oct 23, 2012 at 05:49 PM »

Np Bro

I would reco an external amp para safe. Sayang yung 818 if it gets busted.

rthirtyfourgtr · « **Reply #3045 on:** Oct 23, 2012 at 06:38 PM »

Quote from: jao143 on Oct 23, 2012 at 05:33 PM

Questions mga bros, I'm currently using an onkyo 818. What setting should I use in the speaker set up when I use Left, Right, Center SVS M01 speakers na 4ohms, and an SVS SSS-02 speakers na 8ohms?

Is it also safe for the AVR to use speakers with different impedance?

Thanks.

page 59 on the manual:

Speaker Impedance
4 ohms: Select if the impedance of any speaker is 4 ohms or more but less than 6.
6 ohms: Select if the impedances of all speakers are between 6 and 16 ohms.

when Speaker Impedance is set to 4 ohms, a current limiter is activated within the circuitry so that output power remains within safe operating specs.

impedance ratings as published by speaker manufacturers are average values within the operating bandwidth of the speaker, it's not constant across all frequencies. a speaker rated at 8 ohms may have impedance as low as maybe 6 ohms and can be as high as 50+ ohms.

the 818 is certified for 4 ohms performance, and being THX certified it must also be able to handle as speaker loads as low as 3.2 ohms for short durations.

Quote from: elim on Oct 23, 2012 at 05:38 PM

The 818 might have a hard time with that combination. AFAIK the onkyos can handle different impedances if they're 6 and 8 ohms. however sa literature niya its indicated to avoid using different impedences. If you'd still want to try the setting should be at 4ohms.

i seem to have missed this part...

jao143 · « **Reply #3046 on:** Oct 24, 2012 at 06:42 AM »

I sent an inquiry to OnkyoUSA, here is their response:

(1) When selecting 4 ohm speaker impedance on the receiver; ALL connected speakers must be between 4 ohms. Connecting 4 and 8 ohm speakers onto this unit will cause a imbalanced load and damage the receiver. For instance, you can damage the receiver if using 4 and 8 ohm speakers together on this receiver. (2) You can use 6 and 8 ohms speakers onto this receiver; as the variation is slightly different but is safe for operation of the receiver. (3) Lastly; using an external amp to drive your 4 ohm speakers independently from your 8 ohm speakers connected to the receiver would be derivative based on the external amp and not the TX-NR 818 receiver.

rthirtyfourgtr · « **Reply #3047 on:** Oct 24, 2012 at 08:01 AM »

^ not sure if that is entirely accurate. here is what's stated on the manual (page 15):

Read the following before connecting your speakers:
• You can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more, but less than 6 ohms, be sure to set the minimum speaker impedance to “4ohms” (➔ page 59). If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in protection circuit may be activated.

by the way, did you know that Onkyo's tech support is now handled by a local company?
http://www.tipidpc.com/viewtopic.php?tid=137510

EDIT - similar discussion on AVSForum:

Impedance Differences and Mixing Speakers and Amplifier Impedance Rating
http://www.avsforum.com/t/1264735/impedance-differences-and-mixing-speakers-and-amplifier-impedance-rating

jao143 · « **Reply #3048 on:** Oct 24, 2012 at 08:17 AM »

^

Thank you sir. I will send a pm to astrokidd of Tipidpc

Though, Onkyo USA support na galing yung sagot eh, I just don't know what the local tech support will tell me.

To be safe, I'm not using the 4ohms speakers temporarily, till i get my hands on an external power amp.

rthirtyfourgtr · « **Reply #3049 on:** Oct 24, 2012 at 08:18 AM »

i believe Onkyo USA support is outsourced to a Philippine BPO company. You'll probably get the same answer if that's what was trained to them.

gallery · « **Reply #3050 on:** Nov 09, 2012 at 09:04 AM »

Guys, Question: Will replacing the Cord of your Onkyo receiver to a Branded Power Cord make a big difference?

ultimatedls · « **Reply #3051 on:** Nov 09, 2012 at 09:07 AM »

Quote from: gallery on Nov 09, 2012 at 09:04 AM

Guys, Question: Will replacing the Cord of your Onkyo receiver to a Branded Power Cord make a big difference?

I replaced my pc with a furukawa pc from sir obet "narayan" ok naman

gallery · « **Reply #3052 on:** Nov 09, 2012 at 10:42 AM »

Quote from: ultimatedls on Nov 09, 2012 at 09:07 AM

I replaced my pc with a furukawa pc from sir obet "narayan" ok naman

Okay. Someone is selling me REGA PC for my receiver. A bit pricey so i'm wondering if its worth it.

ultimatedls · « **Reply #3053 on:** Nov 09, 2012 at 11:36 AM »

Quote from: gallery on Nov 09, 2012 at 10:42 AM

Okay. Someone is selling me REGA PC for my receiver. A bit pricey so i'm wondering if its worth it.

I'm using the furukawa on my onkyo and emo got it lang at 1.5k a pc for me worth it yon 1.5k I spent. I'm sure a lot will agree with me if you check his thread a lot gave good comments. From xlo to furukawa ako sir.

rthirtyfourgtr · « **Reply #3054 on:** Nov 09, 2012 at 12:02 PM »

Quote from: gallery on Nov 09, 2012 at 10:42 AM

Okay. Someone is selling me REGA PC for my receiver. A bit pricey so i'm wondering if its worth it.

only you and your ears can decide... home-audition-without-obligation-to-buy first if possible

gallery · « **Reply #3055 on:** Nov 09, 2012 at 12:19 PM »

Quote from: rthirtyfourgtr on Nov 09, 2012 at 12:02 PM

only you and your ears can decide... home-audition-without-obligation-to-buy first if possible

Quote from: ultimatedls on Nov 09, 2012 at 11:36 AM

I'm using the furukawa on my onkyo and emo got it lang at 1.5k a pc for me worth it yon 1.5k I spent. I'm sure a lot will agree with me if you check his thread a lot gave good comments. From xlo to furukawa ako sir.

Thanks for the heads up. I'll probably audition first before finalizing on a 6.5k power cord.

ultimatedls · « **Reply #3056 on:** Nov 09, 2012 at 12:25 PM »

Quote from: gallery on Nov 09, 2012 at 12:19 PM

Thanks for the heads up. I'll probably audition first before finalizing on a 6.5k power cord.

bro obet offers offers that too

gallery · « **Reply #3057 on:** Nov 09, 2012 at 12:36 PM »

Quote from: ultimatedls on Nov 09, 2012 at 12:25 PM

bro obet offers offers that too

How much sir?

ultimatedls · « **Reply #3058 on:** Nov 09, 2012 at 01:16 PM »

Quote from: gallery on Nov 09, 2012 at 12:36 PM

How much sir?

I mean he offers home audition.

Dollarman · « **Reply #3059 on:** Nov 12, 2012 at 04:40 PM »

still looking for my first receiver,,,,anong model ng onkyo should i get? budget 30k to 50k for the receiver. will use it to power either wharfdales or polk. room is about 15ftx18ftx9ft. thanks...