Author Topic: Measy X5 (RTD 1186) Full 3D HD Player (Read 90690 times)

garfield03 · « **Reply #150 on:** Jan 21, 2013 at 11:47 PM »

Quote from: realsteel on Jan 21, 2013 at 05:13 PM

Question here mga sir.

HDTV ko is Toshiba 40PU200 at meron syang built-in media player via USB but when i used my external drive seagate (500gb) to play MKV-DTS file there is no audio coming out from my TV. Will Measy X5 solve this or any NMT? or should I need DTS-capable HDTV? Or I must have both? In short, what do i need to experience DTS audio from my Tosh 40PU200? I dont have 5.1 speakers yet, just using my TV's speakers.

I appreciate your help and suggestions totally new on this home theater experience. Thanks!

Measy X5 will solve your problem or any NMT will do too. You need a separate speaker to produce the FULL Audio Experience of the NMT.

ngek2x · « **Reply #151 on:** Jan 22, 2013 at 09:20 AM »

ang stereoscopic and SBS ba the same?
kaya ba ng measy x5 ang stereoscopic?

josephtan2k · « **Reply #152 on:** Jan 24, 2013 at 02:19 PM »

Sir need help on how to stream videos from measy x5, or if its possible.
I have an LG LED TV in another room which has a wifi dongle attached to it.
Before, I'm able to play movies on the LED TV via wifi, where the movies are in a computer, of course also connected to the network.
Note though that as far as I can remember I needed to place the files in windows media player library and enable streaming.

How can I achieve this in Measy X5?

TIA sirs/mams!

toys4geeks · « **Reply #153 on:** Jan 24, 2013 at 03:58 PM »

Quote from: josephtan2k on Jan 24, 2013 at 02:19 PM

Sir need help on how to stream videos from measy x5, or if its possible.
I have an LG LED TV in another room which has a wifi dongle attached to it.
Before, I'm able to play movies on the LED TV via wifi, where the movies are in a computer, of course also connected to the network.
Note though that as far as I can remember I needed to place the files in windows media player library and enable streaming.

How can I achieve this in Measy X5?

TIA sirs/mams!

Enable samba share po or upnp ,

josephtan2k · « **Reply #154 on:** Jan 24, 2013 at 05:04 PM »

Quote from: toys4geeks on Jan 24, 2013 at 03:58 PM

Enable samba share po or upnp ,

i enabled samba na din and BT.
tried setting up PPPoe pero nagffail when testing.
not sure why and if this is needed.
upnp is also already enabled sa router

josephtan2k · « **Reply #155 on:** Jan 25, 2013 at 02:07 PM »

Has anyone tried putting a 3TB WD Caviar Green internal HDD on the Measy X5?
Just bought one and can't seem to find the drive in windows xp.

Connected the Measy X5's slave port to the desktop's usb port.
I'm still in the office so i'm limited with a computer to troubleshoot.

TIA

toys4geeks · « **Reply #156 on:** Jan 25, 2013 at 02:23 PM »

Quote from: josephtan2k on Jan 25, 2013 at 02:07 PM

Has anyone tried putting a 3TB WD Caviar Green internal HDD on the Measy X5?
Just bought one and can't seem to find the drive in windows xp.

Connected the Measy X5's slave port to the desktop's usb port.
I'm still in the office so i'm limited with a computer to troubleshoot.

TIA

You cant see 3TB full in WinXP, esp. if its prepared via GPT. does it have contents? chances are it is in GPT to see full 3TB.

Use win7 and go disk administrator.

josephtan2k · « **Reply #157 on:** Jan 29, 2013 at 03:44 PM »

How do you install apps here?The manual says you need to download the APK to install the apps.
Can't seem to do this.

I'm trying to install a Media Server App on my Measy X5, anybody tried this already?
My goal is just to make the NMT work like a Media Server so I'd be able to play the files in it in my LED TV wirelessly/via the network.

Thanks

toys4geeks · « **Reply #158 on:** Feb 01, 2013 at 07:01 AM »

Quote from: josephtan2k on Jan 29, 2013 at 03:44 PM

How do you install apps here?The manual says you need to download the APK to install the apps.
Can't seem to do this.

I'm trying to install a Media Server App on my Measy X5, anybody tried this already?
My goal is just to make the NMT work like a Media Server so I'd be able to play the files in it in my LED TV wirelessly/via the network.

Thanks

Would a file share work for you already? enable Samba

As to APK, i think most realtek 1186 players need to write their apk and cant access Google Play directly.

omiboy · « **Reply #159 on:** Feb 16, 2013 at 01:50 AM »

Got hold of a Measy X5 player, I was just wondering why its not being detected properly through LAN. Ang setup is

Cable modem -> Belkin WIFI with LAN support Router -> Measy LAN

naka DHCP yung router but the IP that the player is getting is 168.x.x.x instead of the normal range ng 192.168.x.x

If I look at the network info, pag naka auto setup si Measy through LAN, pati value ng gateway is not there.

May router incompatibility issues ba to? Anybody tried LAN setup?

toys4geeks · « **Reply #160 on:** Feb 16, 2013 at 05:08 AM »

Quote from: omiboy on Feb 16, 2013 at 01:50 AM

Got hold of a Measy X5 player, I was just wondering why its not being detected properly through LAN. Ang setup is

Cable modem -> Belkin WIFI with LAN support Router -> Measy LAN

naka DHCP yung router but the IP that the player is getting is 168.x.x.x instead of the normal range ng 192.168.x.x

If I look at the network info, pag naka auto setup si Measy through LAN, pati value ng gateway is not there.

May router incompatibility issues ba to? Anybody tried LAN setup?

Isolate your network cable in use, baka po maluwag.

if ayaw, force mo by manually assigning IP address 192.168.*.* instead of DHCP, it should see your network fine, as long as its plugged to the same internal network and make sure there are no router rules (i.e. MAC ADDRESS controls for IP address reservations etc/) if all else fail. reset your router to manufacturer default with NMT @ DHCP

omiboy · « **Reply #161 on:** Feb 16, 2013 at 05:21 AM »

Quote from: toys4geeks on Feb 16, 2013 at 05:08 AM

Isolate your network cable in use, baka po maluwag.

if ayaw, force mo by manually assigning IP address 192.168.*.* instead of DHCP, it should see your network fine, as long as its plugged to the same internal network and make sure there are no router rules (i.e. MAC ADDRESS controls for IP address reservations etc/) if all else fail. reset your router to manufacturer default with NMT @ DHCP

will try to isolate later. im using the same cable to connect one of my computer directly. ala naman problem yung laptop if wired or wireless. and nakadefault setup lng yung belkin. im not sure if making it static would solve the problem, baka magkaproblema naman yung ibang devices nakakonek sa router through WIFI.

toys4geeks · « **Reply #162 on:** Feb 16, 2013 at 05:25 AM »

Quote from: omiboy on Feb 16, 2013 at 05:21 AM

will try to isolate later. im using the same cable to connect one of my computer directly. ala naman problem yung laptop if wired or wireless. and nakadefault setup lng yung belkin. im not sure if making it static would solve the problem, baka magkaproblema naman yung ibang devices nakakonek sa router through WIFI.

hindi master basta yung DHCP IP range mo set sa router (i.e. 192.168.1.100 - 192.168.1.150) and the IP you will manually assign is outside that range (192.168.1.199).

omiboy · « **Reply #163 on:** Feb 16, 2013 at 07:59 AM »

Quote from: toys4geeks on Feb 16, 2013 at 05:25 AM

hindi master basta yung DHCP IP range mo set sa router (i.e. 192.168.1.100 - 192.168.1.150) and the IP you will manually assign is outside that range (192.168.1.199).

Router restored to factory defaults. I think the cable is good, kasi either way I connect 2 of the computers (wired or not), nakaka connect sya sa internet.

1. On Measy, tried Network->Wired Lan Setup->DHCP (AUTO)->DNS Auto... Testing... Fail...
Looking at Misc->Network Info, eto na set ni Measy..

IP: 169.254.73.131
Subnet: 255.255.0.0
Gateway 0.0.0.0

These steps below are doomed to fail, anyway just to rule out the possibility

Quote

1.A tried Network->Wired Lan Setup->DHCP (AUTO)->DNS Manual... set to 0.0.0.0... Testing... Fail...
1.B tried Network->Wired Lan Setup->DHCP (AUTO)->DNS Manual... set to <Provider DNS>... Testing... Fail...
1.A tried Network->Wired Lan Setup->DHCP (AUTO)->DNS Manual... set to 192.168.2.1... Testing... Fail...

Looking at Network info, same lang above, except for the IP values

Router's DHCP range is 192.168.2.2 - 192.168.2.100.. so trying to do a fix ip setup for Measy
2. Network->Wired Lan Setup->Fix IP (Manual)

IP: 169.254.73.131
Subnet: 255.255.255.0
Gateway 192.168.2.1
DNS 192.168.2.1

di pa rin nakikita sa network. di ko napi-ping yung assigned ip.. tried turning on/off the modem, router, player.. same result.. the built in browser or apps can't even connect to the net..

did I miss anything?

toys4geeks · « **Reply #164 on:** Feb 16, 2013 at 08:21 AM »

Quote from: omiboy on Feb 16, 2013 at 07:59 AM

Router restored to factory defaults. I think the cable is good, kasi either way I connect 2 of the computers (wired or not), nakaka connect sya sa internet.

1. On Measy, tried Network->Wired Lan Setup->DHCP (AUTO)->DNS Auto... Testing... Fail...
Looking at Misc->Network Info, eto na set ni Measy..

IP: 169.254.73.131
Subnet: 255.255.0.0
Gateway 0.0.0.0

These steps below are doomed to fail, anyway just to rule out the possibility
Router's DHCP range is 192.168.2.2 - 192.168.2.100.. so trying to do a fix ip setup for Measy
2. Network->Wired Lan Setup->Fix IP (Manual)
IP: 192.168.2.131
Subnet: 255.255.255.0
Gateway 192.168.2.1
DNS 192.168.2.1

di pa rin nakikita sa network. di ko napi-ping yung assigned ip.. tried turning on/off the modem, router, player.. same result.. the built in browser or apps can't even connect to the net..

did I miss anything?

omiboy · « **Reply #165 on:** Feb 16, 2013 at 08:28 AM »

^^ opps.. copy/pasted the prev bullet list, di ko napalitan IP..

i tried 192.168.2.200 actually.. fail pa rin..

toys4geeks · « **Reply #166 on:** Feb 16, 2013 at 08:50 AM »

Quote from: omiboy on Feb 16, 2013 at 08:28 AM

^^ opps.. copy/pasted the prev bullet list, di ko napalitan IP.. i tried 192.168.2.200 actually.. fail pa rin..

hmm, is it the LAN port? there any LED indicator (Netactivity?, IsPlugged?)?

omiboy · « **Reply #167 on:** Feb 16, 2013 at 08:55 AM »

Quote from: toys4geeks on Feb 16, 2013 at 08:50 AM

hmm, is it the LAN port? there any LED indicator (Netactivity?, IsPlugged?)?

Yup..kaya i can rule out cable.. And pagnaka on namn yung player, if i remove the cable, nadedetect ni player na nawala yung conn.. Nagpapalit status sa setup screen..

toys4geeks · « **Reply #168 on:** Feb 16, 2013 at 09:21 AM »

Quote from: omiboy on Feb 16, 2013 at 08:55 AM

Yup..kaya i can rule out cable.. And pagnaka on namn yung player, if i remove the cable, nadedetect ni player na nawala yung conn.. Nagpapalit status sa setup screen..

I ran out of ideas

Watch a movie ka muna I am sure someone else will have an idea

omiboy · « **Reply #169 on:** Feb 18, 2013 at 08:59 PM »

Quote from: toys4geeks on Feb 16, 2013 at 09:21 AM

I ran out of ideas Watch a movie ka muna I am sure someone else will have an idea

got a replacement unit..

ok na ang wired measy..

stockHT · « **Reply #170 on:** Mar 25, 2013 at 08:43 PM »

yeah ako I wired it. Less hassle.

stockHT · « **Reply #171 on:** Mar 25, 2013 at 10:22 PM »

guys do we have this kind of screen display for our measy x5?

Galactus · « **Reply #172 on:** Mar 26, 2013 at 11:20 AM »

Yung problem ko sa Measy X5 ko is that it can't copy the main movie file from the internal or external drives to a USB flashdrive. JPEGs and SRTs can be copied but not the main file itself. Tried it over a dozen times, pinagpalit-palit ko na yung USB ports, pero parating ayaw.

Was trying to copy a 4GB, 2GB and 8GB file. Naco-copy yung associated files, but the main movie file itself, ayaw. Tried copying the whole folder, pero same result.

So I boot up my desktop and make the Measy a slave drive. Hooked it up via the slave port, and the X5 interface says that is a now a slave drive. Thing is, my PC can't detect it.

Anybody here have the same problem? How do I resolve this?

Columbia · « **Reply #173 on:** Mar 26, 2013 at 12:25 PM »

Quote from: Galactus on Mar 26, 2013 at 11:20 AM

Yung problem ko sa Measy X5 ko is that it can't copy the main movie file from the internal or external drives to a USB flashdrive. JPEGs and SRTs can be copied but not the main file itself. Tried it over a dozen times, pinagpalit-palit ko na yung USB ports, pero parating ayaw.

Was trying to copy a 4GB, 2GB and 8GB file. Naco-copy yung associated files, but the main movie file itself, ayaw. Tried copying the whole folder, pero same result.

So I boot up my desktop and make the Measy a slave drive. Hooked it up via the slave port, and the X5 interface says that is a now a slave drive. Thing is, my PC can't detect it.

Anybody here have the same problem? How do I resolve this?

Had encountered this before but the solution to the problem is all about how the USB flashdrive was formatted. Make sure that it is NTFS..

garfield03 · « **Reply #174 on:** Apr 01, 2013 at 01:24 AM »

Features: Measy X5 has a Eject Button for Hard Drive or any USB plug in.

balarila · « **Reply #175 on:** Apr 30, 2013 at 02:52 PM »

Hello, everyone!

I've been a member for quite some time now but never posted. Just lurked and learned.

In the midst of refurbishing my 8-year old home theater. Started by calculating 1st reflection points and installed some fiberglass and rockwool. I have a 3D 1080p projector, receiver, and blu-ray player coming mid-May.

Decided to get a Measy X5 yesterday in anticipation of my new gear. I then got a 2TB hard disk and loaded it with some goodies.

Now the question: Can I just insert the loaded hard disk into the X5 or do I need to format it first in the X5? The manual says I need to format the drive first. But it's already full of media and it'll be difficult to offload the contents first.

I inserted it anyway, plugged into my old 1080p TV, turned on, and everything seems to work fine. Just wondering if I may be missing some features if I did not format the drive inside the X5, as the X5 may have some proprietary format process that installs some software.

Appreciate any advice!

toys4geeks · « **Reply #176 on:** Apr 30, 2013 at 02:57 PM »

Format just does the folders and possibly look for the folders and folder permissions if you will do torrent download.

pero if playback lang, ok ka na, just enjoy it a player. NMTs promise a lot of feature that are half baked or unstable so spare yourselves from the frustration and just enjoy it as a player.

balarila · « **Reply #177 on:** Apr 30, 2013 at 04:23 PM »

Thanks, toys4geeks. I know my way around bits and bytes but I also know the value of being content with what one has in technology and avoiding the "frustrations" you mentioned.

Yes, I am enjoying my new NMT.

I will hopefully post more meaningful experience when I finish my setup.

Cheers!

garfield03 · « **Reply #178 on:** Apr 30, 2013 at 10:46 PM »

@Balarila

Cheers! For Your New NMT

runjel · « **Reply #179 on:** May 31, 2013 at 10:40 PM »

ask ko lang mga sir.. un s measy player ko once na ipress subtitle papakita nya subtitle after 5 secs tapos after nun mawawala.. ano kaya problem?